Deako Smart Lighting | 3-Way

Section title

New Install

3-Way


  • Installation Overview
  • Install Deako Backplates
  • Plug in Deako Switch
  • Simple Switch
  • Smart Switch
  • Smart Dimmer
  • Installation Complete

Installation Overview


This installation guide will walk you through installing Deako Switches in a 3-way circuit.

Navigation

Tap the menu icon above at any time to navigate through the installation guide.



Step 1 of 7

Turn off the power


Identify the appropriate circuit breaker at your panel and flip it to the off position.

Step 2 of 7

Strip existing wires


Strip the wires coming out of the wall to 3/8". Do not shorten the Deako Backplate wires.

Step 3 of 7

Trim yellow wires


Using wire cutters, trim the yellow wires on both Deako Backplates so that they are flush to the plastic (you will not need these).

Step 4 of 7

Connect wires


Using wire nuts, connect the wires as show in the diagram above

Step 5 of 7

Screw in Deako Backplate


  • a. Carefully manage wires into the junction box
  • b. Once backplate can be pressed flush to wall, screw the Deako Backplate into the junction box using included screws

Step 6 of 7

Repeat for each switch in the circuit


Move to the next switch in the circuit and repeat this section for that switch.
Once you have installed both Deako Backplates in the 3-way circuit, continue to the next step.

Step 7 of 7

Turn the power on


Identify the appropriate circuit breaker at your panel and flip it to the on position.

What kind of switches are you installing?



Deako Simple Switch


Deako Smart Switch


Deako Smart Dimmer



Step 1 of 3

Plug in a Deako Simple Switch


Install a Deako Simple Switch into one of the Deako Backplates.

  • a. Insert the switch into the Deako Backplate
  • b. Align the blue tab with the slot on the Deako Switch
  • c. While pressing the switch inwards, push in the blue tab

Step 2 of 3

Snap on Deako Faceplate


Install the Deako Faceplate by snapping it onto the backplate.

Step 3 of 3

Repeat for each switch in the circuit


Move to the next switch in the circuit and repeat this section for each switch in the circuit.
Once you have installed Deako Simple Switches into each switch in the circuit, continue to the next step.


Step 1 of 4

Plug in a Deako Smart Switch


Install a Deako Smart Switch into one of the Deako Backplates.

  • a. Insert the switch into the Deako Backplate
  • b. Align the blue tab with the slot on the Deako Switch
  • c. While pressing the switch inwards, push in the blue tab

Step 2 of 4

Snap on Deako Faceplate


Install the Deako Faceplate by snapping it onto the backplate.

Step 3 of 4

Repeat for each switch in the circuit


Move to the next switch in the circuit and repeat this section for each switch in the circuit.
Once you have installed Deako Smart Switches into each switch in the circuit, continue to the next step.

Step 4 of 4

3-way & 4-way linking


Deako Smart Switches and Smart Dimmers are single-pole by default. To change them into 3-way and 4-way switches, follow the instructions above.

If you would prefer written instructions, click here.

Troubleshooting

If a switch continues flashing for more than a minute, exit pairing mode by pressing and holding the switch for 6 seconds. Then, before retrying, factory reset each switch in the circuit. How do I factory reset a Deako Switch?



Step 1 of 5

Plug in a Deako Smart Switch at the line location


Install a Deako Smart Switch into the line location of the circuit.

  • a. Insert the switch into the Deako Backplate
  • b. Align the blue tab with the slot on the Deako Switch
  • c. While pressing the switch inwards, push in the blue tab

If you need help identifying your line and load locations, check out How to do I find the line and load locations?


Deako Smart Dimmers must only be installed at the load location of the circuit


Step 2 of 5

Snap on Deako Faceplate


Install the Deako Faceplate by snapping it onto the backplate.

Step 3 of 5

Plug in a Deako Smart Dimmer at the load location


Install a Deako Smart Dimmer into the load location of the circuit.

  • a. Insert the switch into the Deako Backplate
  • b. Align the blue tab with the slot on the Deako Switch
  • c. While pressing the switch inwards, push in the blue tab

If you need help identifying your line and load locations, check out How to do I find the line and load locations?


Deako Smart Dimmers must only be installed at the load location of the circuit


Step 4 of 5

Snap on Deako Faceplate


Install the Deako Faceplate by snapping it onto the backplate.

Step 5 of 5

3-way & 4-way linking


Deako Smart Switches and Smart Dimmers are single-pole by default. To change them into 3-way and 4-way switches, follow the instructions above.

If you would prefer written instructions, click here.

Troubleshooting

If a switch continues flashing for more than a minute, exit pairing mode by pressing and holding the switch for 6 seconds. Then, before retrying, factory reset each switch in the circuit. How do I factory reset a Deako Switch?


You're all done!


If you have installed Deako Smart Products, click below to learn more about the Deako App.


Have more Deako Switches to install?


If you would prefer a PDF of the installation guide, click here to download it.